A well tuned burner gives the optimum performance of the steam boiler. This requires a careful setting of air flow, fuel flow and the swirl level which ensures air fuel mixing.
Tuning a front wall fired burner firing any fuel, gas or oil or coal, first requires the air flow equalization in all burners. This is carried out by equalizing the pressure after the individual burner isolating damper in the windbox or the air inlet duct to the burner.
The steps involved:
First look at the above two figures in the O & M manual of the boiler you are tuning and understand the steps fully
Note the burner setting details for start-up
The Tertiary Air swirl position for all burners and all vanes set at the recommended open position (Many burner manufactures use 30 degree open) to moderate swirl
The Secondary Air swirl position are normally factory set at a specified open position (here also burner designers prefer 30 degree open) to moderate swirl
Generally the SA flow control damper positions are all set at fully open position
All shrouds are set uniformly at the same position to produce approximately the recommended windbox to furnace differential pressure, better to keep any variation within plus minus 15 % deviation
Igniter to be set as per manufacturer guide lines.
As the boiler load increases the windbox to furnace drop increases from a lower value to the required maximum value from a load of 50% to 100%
The flame in burner will be approximately as shown in the figure. In the case of coal burner the coal stream extends only 1 to 3 inches before rapid ignition occurs.
Manual biasing can be done in most of the coal burners to modify the relative position of each shroud with respect to the other. This is required to be provided by the operator
The ability to balance air flow on burners in service at each burner level. This is done by observing the air velocity indication at each burner and individually biasing the shroud in each burner
Capability to manually adjust the total burner level air flow to attain a certain degree of off-stoichiometry with respect to mill load at that level.
Many burner designers prefer to provide two airflow measurement: one upstream of the secondary and the other upstream of the tertiary air.
Any deviation in burner setting can be evaluated from the performance changes that occur during continuous operation. The parameters like unburned carbon in ash, the CO levels, the flame colour, and the smoky tail of the burner are some of the indications that need the operator attention. The flame length variation and the NOx level variations are the other parameters that need to be addressed.
Source: http://www.zgsteamboiler.com/news/Tuning-of-Front-Wall-Coal-Burners-in-Large-Capacity-Boilers.html
Pre: Boiler Designers Use Different Materials in Super heaters
Next: How Large Boiler Drums are Manufactured
Packaging Detail:Wooden box package of Tuning of Front Wall Coal Burners in Large Capacity Boilers
Delivery Detail:20-40 days after payment
We have over 70 years' experience of industrial steam boiler and autoclave, and we have a professional installation and after-sales staff for products.Take advantage of the most economical way to improve efficiency and operating flexibility, Get substantial savings on your fuel costs,Reduce all emissions for each K/W of electricity generated, including CO2.
Our industrial steam boiler manufactured strictly according to national and international standard. our products have approved ASME, IBR, ISO9001-2008, etc
All our company's products are 100% factory inspected to ensure the high quality.
We provide one year quality warranty service, please rest assured purchase.
ZG service ensures that this will not happen. During installation of industrial steam boiler, 1-2 experienced engineering and technical personnel will be sent for the site representative for technical tests and installation instructions free of charge; processing the various problems arising in the course timely while installing.
Established:In 1945
Number of Employees:above 1500 People
Our products:industrial horizontal steam boiler and hot water boiler(biomass boiler, gas boiler, oil boiler, coal boiler, etc), CFB boiler, power plant boiler, waste heating recovery boiler, Pressure Vessel(AAC autoclave, Curing tank,etc )
Factory Size (Sq.meters):400,000 square meters
Factory Location:Factory 1: Zhengzhou,,Henan, China. Factory 2: Xingyang,Henan,China
Number of R&D Staff:376 people
Export Percentage:30-40%
Total Annual Sales Volume:US$100 Million
Main Market:South America(Colombia, Venezuela, Guyana, Suriname, Ecuador, Peru, Brazil, Bolivia, Chile, Paraguay, Uruguay, Argentina and French Guiana), North America(Bahamas, Canada, Costa Rica, Cuba, El Salvador, Guatemala, Honduras, Haiti, Jamaica, Mexico, Nicaragua, Panama), Eastern Asia(Mongolia / Russia / North Korea / South Korea / Japan), Oceania(Australia, New Zealand, Fiji), Mid East(Bahrain, Egypt, Iran, Iraq, Israel, Jordan, Kuwait, Lebanon, Oman, Qatar, Saudi Arabia, Syria, UAE and Yemen, Palestine, Algeria, Libya, Morocco, Tunisia and Sudan, Mauritania and Somalia), Africa(Egypt, Sudan, Libya, Tunisia, Algeria, Morocco, Ethiopia, Somalia, Kenya, Tanzania, Sierra Leone, Liberia, Cote d'Ivoire, Ghana, Togo, Niger, Nigeria, Cameroon, Gabon, Congo (Brazzaville), Zambia, Zimbabwe, Angola, Mozambique, Botswana, Namibia, South Africa), South Asia(Nepal, Bhutan, India, Pakistan, Bangladesh, Sri Lanka, Maldives) Southeast Asia(Vietnam, Laos, Cambodia, Thailand, Myanmar, Malaysia, Singapore, Indonesia, Brunei, the Philippines, East Timor) Domestic Market(China)
Source: http://www.zgsteamboiler.com/news/Tuning-of-Front-Wall-Coal-Burners-in-Large-Capacity-Boilers.html
Pre: Boiler Designers Use Different Materials in Super heaters
Next: How Large Boiler Drums are Manufactured
Get Price And Support
Simply complete the form below, click submit, you will get the price list and a ZG boiler representative will contact you within one business day. Please also feel free to contact us by email or phone. ( * Denotes a required field ).
Email: [email protected]
Tele: +86 17719993430